| R019 | ELVX PHONE TRANSMITTER ELEMENT |
| R028 | DIRECTRY PANEL BULB-LONG ELVOX |
| R060 | PLASTIC PUSHBUTTON/NAMEHOLDER |
| R088 | REPLACEMENT COIL CORD FOR 870W WHITE COLOR. MAY ALSO BE USED WITH 5401 SERIES VIDEO MONITORS (IN WHITE) |
| R1 | APT. BUZZER CALL PULSATOR UNIT USED IN ADDITION TO 2/3/5 WIRE APT. AMPLIFIERS FOR PULSATING BUZZERS AT INDIV. APT. DOORS |
| R12 | 8VAC DOOR RELEASE RELAY UNIT/S USED WITH SP300 CONTROLLER TO ACTIVATE AN ELECTRIC DOOR RELEASE |
| R2006 | S.T.R. ALPHATONE SIGNAL ADAPTR USE WITH S.T.R. HT2006 SERIES HANDSETS ONLY---WHEN USED WITH THE NH208TVU POWER SUPPLY ONLY |
| R2006I | ALPHATONE SIGNAL ADAPTR INSTLD |
| R2007 | 16VAC ALPHATONE SIGNAL ADAPTOR USE IN PLACE OF BUZZER IN THE HT2000 AND/OR HT3000 SERIES HANDSETS - OR STAND-ALONE |
| R2007I | ALPHATONE SIGNAL ADAPTR INSTLD |
| R2007S | ALPHATONE SIGNAL UNIT-SURF MT. WALNUT PLASTIC FINISH SURFACE MOUNTS RIGHT ON WALL OR OVER 1-GANG ELECTRICAL BOX |
| R2008 | 3-NOTE ALPHATONE SIGNAL ADAPTR |
| R203 | LOCK FOR VANDAL-RES. PANEL(S) |
| R3 | PASO FM TUNER UNIT-----120VAC (OPERATES ON 120VAC) |
| R4SS | SURGE PROTECTOR---RS485 CONNEC 2000AMP PROTECTION |
| R631 | 6300 BACKPLATE CONNECTOR UNIT FOR 6300 ELVOX MONITOR |
| R8 | CALL TONE GENERATOR UNIT-STND. |
| RA-A | MASTER STAT-DESK/WALL--RAX/RCX |
| RA-B | FLUSH MT. ST. STEEL MASTER-RCX |
| RA-D | MASTER STAT-DESK/WALL--RAX/RCX |
| RAX-CEU | CENTRAL EXCHANGE UNIT-RAX SER. OPERATES ON 120VAC REQ. 1 OR MORE XC-063A CARDS REQ. PS-2420UL FOR 'ALL-CALL' |
| RB500 | RING BRIDGE INTERFACE UNIT(S) |
| RB8 | CEIL SPKR. BAFFLE-8"-WHITE-RD. |
| RB8P | WALL SPKR. BAFFLE-8"-WHITE-SQ. |
| RB8S | CEILING SPEAKER--ROUND--8 OHMS USE WITH IH008 MOUNTING RING AND (OPTIONAL) PH8-1 ENCLOSURE |
| RB8SP | SURF MT. SPEAKER-SQUARE-8 OHMS WHITE-SQUARE-PLASTIC ENCLOSURE NO LINE TRANSFORMER INCLUDED SURFACE WALL OR CEILING MOUNT |
| RB8ST | CEILING SPEAKER-ROUND--25V/70V USE WITH IH008 MOUNTING RING AND (OPTIONAL) PH8-1 ENCLOSURE BUILT-IN 25/70V LINE TRANSF. |
| RB8ST25 | CEILING SPEAKER-ROUND--25 VOLT USE WITH IH008 MOUNTING RING AND (OPTIONAL) PH8-1 ENCLOSURE BUILT-IN 25 VOLT LINE TRANSF. |
| RB8STP | SURF MT SPEAKER-SQUARE-70 VOLT WHITE-SQUARE-PLASTIC ENCLOSURE BUILT-IN 70 VOLT LINE TRANSF. SURFACE WALL OR CEILING MOUNT |
| RB8STV | CEILING SPEAKER-70V+VOL CONTR. USE WITH IH008 MOUNTING RING AND (OPTIONAL) PH8-1 ENCLOSURE BUILT-IN 70 VOLT LINE TRANSF. |
| RC0100/4 | 100 OHM CARBON RESISTOR---1/4W |
| RC013 | 75 OHM CARBON RESISTOR-1/4W-5% |
| RC034 | 4700 OHM CARBON RESISTOR--1/2W |
| RC1004 | RECTIFIER MAX 100VAC--MAX 4AMP |
| RCA-V | COAX VIDEO CONNECTOR WITH RING |
| RCPL-R5 | PLATEA WALL MOUNT CONNECTOR |
| RCPL-UNO | PLATEA WALL MOUNT CONNECTOR |
| RCPL-V2PLUS | PLATEA WALL MOUNT CONNECTOR |
| RCSH-562 | SWITCHBOARD WALL MOUNT ADAPTOR |
| RCSH-PLUS | SWITCHBOARD WALL MOUNT ADAPTOR USED WITH CE-941 PLUS AND/OR CE-990 PLUS PORTER SWITCHBOARD STATION(S) |
| RCX-128 | CENTRAL EXCHANGE UNIT-RCX SER. REQUIRES 1 TO 16 MODEL XC-092 8-STATION SUBSCRIBER CARDS |
| RCX-48 | CENTRAL EXCHANGE UNIT-RCX SER. REQUIRES 1 TO 6 MODEL XC-092 8-STATION SUBSCRIBER CARDS |
| RCX-88 | CENTRAL EXCHANGE UNIT-RCX SER. REQUIRES 1 TO 11 MODEL XC-092 8-STATION SUBSCRIBER CARDS |
| RD-PLUS/UNO | DIGITAL REPEATER---UNO SYSTEMS |
| RELAY-8 | 8 OUTPUT SIGNAL RELAY BOARD(S) REQUIRES KE-232IF CABLE AND KE-PWR5/2A 5VDC POWER SUPPLY |
| RJ1012 | 12V/10W VVT PANEL HALOGEN BULB USE WITH 'VVT' CAMERA ASSEMBLY (DO NOT TOUCH WITH BARE HANDS) (FINGER OILS CAN DAMAGE BULB!) |
| RJ71CJK | RJ71 JACK FOR 'NO PHONE BILL' (1) REQUIRED FOR EACH 'LIB' BOARD (12 APARTMENTS/LINES) ON AN OVATION SYSTEM |
| RLB932 | RELAY BOARD FOR AA903C / AA917 |
| RLK-8 | SURF. VANDAL BAFFLE FOR 8" SPK REQUIRES HRP832 SCREWDRIVER DOES NOT INCLUDE SPEAKER UNIT |
| RM027 | CM400 SER. LEXAN DIRECT WINDOW |
| RM042 | MIRROR-3" X 3" FOR VM/VT PANEL |
| RM067 | CM490 SER. LEXAN DIRECT WINDOW |
| RM076 | 35 PAPER INSERTS FOR RP084/085 USED IN AM612 AND AM642 SERIES PANELS. |
| RM3175SB | 20GAS/C STEEL BRACKET-3"X1.75" USED TO INSTALL BUZZERS INTO THE BACK OF THE LI381 TYPE DOME LAMPS |
| RM3175SP | 20GAS/C STEEL PLATE---3"X1.75" USED TO INSTALL BUZZERS INTO THE BACK OF THE LI381 SER DOME MUST BE BENT AND DRILLED |
| RM5000/08 | CENTRAL EXCHANGE UNIT---8 CAP. CONTAINS 4 LINKS/1 PROG. CHAN. REQUIRES 2- BAT12-30 BATTERIES FOR BATTERY BACK-UP OPTION |
| RM5000/16 | CENTRAL EXCHANGE UNIT--16 CAP. CONTAINS 4 LINKS/1 PROG. CHAN. REQUIRES 2- BAT12-30 BATTERIES FOR BATTERY BACK-UP OPTION |
| RM5000/24 | CENTRAL EXCHANGE UNIT--24 CAP. CONTAINS 4 LINKS/1 PROG. CHAN. REQUIRES 2- BAT12-30 BATTERIES FOR BATTERY BACK-UP OPTION |
| RM5000/32 | CENTRAL EXCHANGE UNIT--32 CAP. CONTAINS 4 LINKS/1 PROG. CHAN. INCLUDES 2- BAT12-30 BATTERIES FOR BATTERY BACK-UP CAPABILITY |
| RM5000/40 | CENTRAL EXCHANGE UNIT--40 CAP. CONTAINS 4 LINKS/1 PROG. CHAN. INCLUDES 2- BAT12-30 BATTERIES FOR BATTERY BACK-UP CAPABILITY |
| RM5000/48 | CENTRAL EXCHANGE UNIT--48 CAP. CONTAINS 4 LINKS/1 PROG. CHAN. INCLUDES 2- BAT12-30 BATTERIES FOR BATTERY BACK-UP CAPABILITY |
| RM5000/56 | CENTRAL EXCHANGE UNIT--56 CAP. CONTAINS 4 LINKS/1 PROG. CHAN. INCLUDES 2- BAT12-30 BATTERIES FOR BATTERY BACK-UP CAPABILITY |
| RM5000EX/08 | CENTRAL EXCHANGE UNIT--8 CAP. CONTAINS 3 LINKS/1 PROG. CHAN. REQUIRES 2- BAT12-30 BATTERIES FOR BATTERY BACK-UP OPTION |
| RM5000EX/24 | CENTRAL EXCHANGE UNIT--24 CAP. CONTAINS 3 LINKS/1 PROG. CHAN. REQUIRES 2- BAT12-30 BATTERIES FOR BATTERY BACK-UP OPTION |
| RM5000EX/32 | CENTRAL EXCHANGE UNIT--32 CAP. CONTAINS 3 LINKS/1 PROG. CHAN. INCLUDES 2- BAT12-30 BATTERIES FOR BATTERY BACK-UP CAPABILITY |
| RM5000EX/40 | CENTRAL EXCHANGE UNIT--40 CAP. CONTAINS 3 LINKS/1 PROG. CHAN. INCLUDES 2- BAT12-30 BATTERIES FOR BATTERY BACK-UP CAPABILITY |
| RM5000EX/48 | CENTRAL EXCHANGE UNIT--48 CAP. CONTAINS 3 LINKS/1 PROG. CHAN. INCLUDES 2- BAT12-30 BATTERIES FOR BATTERY BACK-UP CAPABILITY |
| RM5000EX/56 | CENTRAL EXCHANGE UNIT--56 CAP. CONTAINS 3 LINKS/1 PROG. CHAN. REQUIRES 2- BAT12-30 BATTERIES FOR BATTERY BACK-UP OPTION |
| RO-ADC722WP | DAY/NGHT IR BULLET CAMERA-4MM REQUIRES SEP. POWER SUPPLY |
| RP/S-25 | AUX. INPUT CORD AND PLUG SET |
| RP021 | WHITE INNER PLASTIC TAB ONLY |
| RP021CM | ANNUN LENS CAP+CUSTOM MARKINGS |
| RP022 | ST014 LENS CAP ONLY-AMBER TYPE |
| RP022K | ST014 LENS CAP ONLY-AMBER-10PK |
| RP023 | ST014 LENS CAP ONLY--RED COLOR |
| RP024 | ST014 LENS CAP ONLY-GREEN TYPE |
| RP024K | ST014 LENS CAP ONLY-GREEN-10PK |
| RP027 | ST014 LENS CAP ONLY-CLEAR TYPE |
| RP027K | ST014 LENS CAP ONLY-CLEAR-10PK |
| RP028 | ST014 LENS CAP ONLY-YELLOW COL |
| RP028K | ST014 LENS CAP ONLY-YELLO-10PK |
| RP037A | RED RUBBER BULB COVER/SLEEVE |
| RP037AK | RED RUBBER BULB COVERS---10PAK |
| RP050 | WHITE SWITCH CAP ONLY-IR704B'S USED ON 3-SWITCH ASSEMBLY FOR IR704B OR 4-SWITCH ASSEMBLY FOR IR704BD STATIONS |
| RP051 | GREY SWITCH CAP ONLY--IR704B'S USED ON 3-SWITCH ASSEMBLY FOR IR704B OR 4-SWITCH ASSEMBLY FOR IR704BD STATIONS |
| RP052 | GREY SWITCH CAP ONLY-SM400 SEL USED ON THE INDIVIDUAL SELECTIVE SWITCHES ON THE SM400 SERIES MASTERS |
| RP053 | BLACK SWITCH CAP ONLY-IR704B'S USED ON 3-SWITCH ASSEMBLY FOR IR704B OR 4-SWITCH ASSEMBLY FOR IR704BD STATIONS |
| RP054 | RED SWITCH CAP ONLY---IR704B'S USED ON 3-SWITCH ASSEMBLY FOR IR704B OR 4-SWITCH ASSEMBLY FOR IR704BD STATIONS |
| RP055A | ALUM PANEL PLUNGER-SMALL-ALUM. |
| RP055B | TEK-GUARD PLUNGER--ALUM.-BLANK |
| RP055B-BLK | TEK-GUARD PLUNGER--BLACK-BLANK |
| RP055BE | TEK-GUARD PLUNGER-BLACK-ENGRVD |
| RP055EN | ENGRAVING ONLY OF PANEL PLUNGR |
| RP071A | GREEN RUBBER BULB COVER/SLEEVE |
| RP071AK | GREEN RUBBER BULB COVERS-10PAK |
| RP072A | YELLOW RUBBER BULB COVR/SLEEVE |
| RP084 | NAME HOLDER BASE---AM612/AM642 USE WITH RP085 LENS COVER AND RM076 PAPER INSERTS |
| RP084K | NAME HOLDER BASE-AM6 SER-25PAK USE WITH RP085 LENS COVER AND RM076 PAPER INSERTS |
| RP085 | NAMEHOLDER COVER---AM612/AM642 USE WITH RP084 PLASTIC BASE AND RM076 PAPER INSERTS |
| RP085K | NAME HOLDER COVER-AM6SER-25PAK USE WITH RP085 LENS COVER AND RM076 PAPER INSERTS |
| RP088 | WHITE LENS ONLY-LI380/384 DOME USED WITH LI380 OR LI384A 4-LENS SECTION (OR EQUIVALENT) CORRIDOR LIGHT ONLY |
| RP088K | 10PAK WHITE LENS ONLY-LI380SER USED WITH LI380 OR LI384A 4-LENS SECTION (OR EQUIVALENT) CORRIDOR LIGHT ONLY |
| RP089 | AMBER LENS ONLY-LI380/384 DOME USED WITH LI380 OR LI384A 4-LENS SECTION (OR EQUIVALENT) CORRIDOR LIGHT ONLY |
| RP089K | 10PAK AMBER LENS ONLY-LI380SER USED WITH LI380 OR LI384A 4-LENS SECTION (OR EQUIVALENT) CORRIDOR LIGHT ONLY |
| RP090 | GREEN LENS ONLY-LI380/384 DOME USED WITH LI380 OR LI384A 4-LENS SECTION (OR EQUIVALENT) CORRIDOR LIGHT ONLY |
| RP090K | 10PAK GREEN LENS ONLY-LI380SER USED WITH LI380 OR LI384A 4-LENS SECTION (OR EQUIVALENT) CORRIDOR LIGHT ONLY |
| RP091 | RED LENS ONLY--LI380/384A DOME USED WITH LI380 OR LI384A 4-LENS SECTION (OR EQUIVALENT) CORRIDOR LIGHT ONLY |
| RP091K | 10 PAK RED LENS ONLY--LI380SER USED WITH LI380 OR LI384A 4-LENS SECTION (OR EQUIVALENT) CORRIDOR LIGHT ONLY |
| RP092 | WHITE LENS ONLY-LI381/382 DOME USED WITH LI381/LI382 1-PIECE (OR EQUIVALENT) CORRIDOR LIGHT ONLY |
| RP092K | 10PAK WHITE LENS ONLY-LI381SER USED WITH LI380 OR LI384A 4-LENS SECTION (OR EQUIVALENT) CORRIDOR LIGHT ONLY |
| RP100 | BLUE LENS ONLY-LI380/384A DOME USED WITH LI380 OR LI384A 4-LENS SECTION (OR EQUIVALENT) CORRIDOR LIGHT ONLY |
| RP100K | 10 PAK BLUE LENS ONLY-LI380SER USED WITH LI380 OR LI384A 4-LENS SECTION (OR EQUIVALENT) CORRIDOR LIGHT ONLY |
| RP111 | 1 FOOT GASKET FOR AM612/AM642 |
| RP129 | WHITE SWITCH CAP ONLY----ST112 USED WITH THE ST112 DOOR RELEASE SWITCH ON THE SM404 SM406 AND SM411 MASTER(S) |
| RP138 | 10PK. WATER RESIS COVERS-SF067 CLEAR PLASTIC WITH ADHESIVE TABS FOR SF067 PENDANT UNIT (THIS MODEL# IS FOR A 10 PACK) |
| RP-20 | 1-GANG ST ST PLATE W/'D' HOLE |
| RP-21 | 1-GANG ST ST PLATE W/LOCK HOLE |
| RP-22 | 1-GANG STST PLATE W/SONLRT HOL |
| RP-23 | 1-GANG STST PLATE W/PIEZO HOLE USE WITH PA-100 PIEZO BUZZER |
| RP-26 | MOMEN. PUSHBUTTON W/PLATE+RING INCLUDES K13 BUTTON/SWITCH AND 10C PROTECTIVE GUARD RING WITH STAINLESS STEEL PLATE |
| RP397BK | 5PAK BUNGEE CORDS-NC397A PAGER USED WITH THE NC397 AND/OR NC397A POCKET PAGER - PACK (KIT) OF 5 PIECES |
| RP397HK | 5PACK HOLSTER BELT CLIP-NC397A USED WITH THE NC397 AND/OR NC397A POCKET PAGER (PACK OF 5 PIECES) |
| RP397RB | RUBBER PROTECTIVE COVER-NC397A USED WITH THE NC397A POCKET PAGER(S) - LIGHT GREY RUBBER WITH CLEAR PLASTIC WINDOW |
| RP399H | REPL. HOLSTER BELT CLIP-NC399P USED WITH THE NC399P POCKET PAGER |
| RP-44 | LOCKING PUSHBUTTON+ST ST PLATE INCLUDES FA-200 BUTTON/SWITCH WITH STAINLESS STEEL PLATE USE WITH OPTIONAL 11C-BLK RING |
| RP-44MWH | MOMEN. PUSHBUTTON+WHITE PLATE INCLUDES FA-200 BUTTON/SWITCH WITH WHITE FINISH PLATE USE WITH OPTIONAL 11C-BLK RING |
| RP-44WH | LOCKING PUSHBUTTON+WHITE PLATE INCLUDES FA-200 BUTTON/SWITCH WITH WHITE FINISH PLATE USE WITH OPTIONAL 11C-BLK RING |
| RP501 | REPL. NECKLACE+CLIP FOR SF501 |
| RP503 | SMALL WRISTBAND FOR SF501 PEND USED WITH THE SF501 PENDANT (USUALLY USED BY WOMEN) |
| RP504 | LARGE WRISTBAND FOR SF501 PEND USED WITH THE SF501 PENDANT (USUALLY USED BY MEN) |
| RS-20BW | 120VAC 20" B + W MONITOR--120V OPERATES ON 120VAC |
| RS816 | 16 REMOTE CAP. MASTER STATION WALL OR DESK MOUNT TYPE. CAN BE USED WITH RS840 EXPANDER. REQUIRES PK800A POWER SUPPLY |
| RS816R | 16 REMOTE CAP. MASTER STATION WALL OR DESK MOUNT TYPE. CAN BE USED WITH RS840-REFURBISHED REQUIRES PK800A POWER SUPPLY |
| RS840 | 24 STATION MASTER EXPANDER(S) WALL OR DESK MOUNT TYPE. USED IN ADDITION TO RS816 MASTER. MAY REQ. PK800A POWER SUPPLY |
| RS850 | 50 STAT. REMOTE LED INDICATOR WALL OR DESK MOUNT TYPE. USED IN ADDITION TO RS816 MASTER. MAY REQ. PK800A POWER SUPPLY |
| RSM404 | 4 STAT. LED ROOM STATUS MODULE HAS 4-ROOM STATUS L.E.D. SETS RED/YELLOW/GREEN/WHITE. USE WITH 'MT' SERIES FRAME(S) |
| RSM408 | 8 STAT. LED ROOM STATUS MODULE HAS 8-ROOM STATUS L.E.D. SETS RED/WHITE (DOUBLE) USE WITH 'MT' SERIES FRAME(S) |
| RSP-1 | SELECTIVE PAGING RELAY--DPDT OPERATES ON 120VAC. IT IS USED TO PROVIDE ZONE PAGING CAPABILITIES ON PAGING SYSTEMS |
| RSS402 | 2 BUTTON ROOM STATUS STATION HAS 2-ROOM STATUS SWITCHES RED/WHITE. MUST BE USED WITH ALPHASTATUS SYSTEM ONLY |
| RSS403 | 3 BUTTON ROOM STATUS STATION HAS 2-ROOM STATUS SWITCHES RED/WHITE. MUST BE USED WITH ALPHASTATUS SYSTEM ONLY |
| RSS404 | 4 BUTTON ROOM STATUS STATION HAS 4-ROOM STATUS SWITCHES RED/WHITE/YELLOW/GREEN. USED WITH ALPHASTATUS SYSTEM ONLY |
| RSS405 | 5 BUTTON ROOM STATUS STATION HAS 4-ROOM STATUS SWITCHES RED/WHITE/YELLOW/GREEN. USED WITH ALPHASTATUS SYSTEM ONLY |
| RSS406 | 6 BUTTON ROOM STATUS STATION HAS 6-ROOM STATUS SWITCHES RED/WHITE/YELLOW/GREEN/BLUE AND AMBER---ALPHASTATUS SYSTEM |
| RSS407 | 7 BUTTON ROOM STATUS STATION HAS 6-ROOM STATUS SWITCHES RED/WHITE/YELLOW/GREEN/BLUE AND AMBER---ALPHASTATUS SYSTEM |
| RTL | AUX. HANDSET SPEAKER-8 OHM-RND 50MM DIAMETER (ROUND) |
| RTM1 | 1 PUSHBUTTON STANDARD MODULE WITH BUILT-IN L.E.D. PRISM ILLUMINATION. L.E.D. OPERATES ON 8-12V / 40 MA. |
| RTM1A | 1 PUSHBUTTON 2-WIRE ALP MODULE WITH BUILT-IN L.E.D. PRISM ILLUMINATION. L.E.D. OPERATES ON 8-12V / 40 MA. |
| RTM1AB | 1 BUTTON 2-WIRE MODULE---BROWN WITH BUILT-IN L.E.D. PRISM ILLUMINATION. L.E.D. OPERATES ON 8-12V / 40 MA. |
| RTM1AT | 1 BUTTON 2-WIRE MODULE---TITAN WITH BUILT-IN L.E.D. PRISM ILLUMINATION. L.E.D. OPERATES ON 8-12V / 40 MA. |
| RTM1AW | 1 BUTTON 2-WIRE MODULE---WHITE WITH BUILT-IN L.E.D. PRISM ILLUMINATION. L.E.D. OPERATES ON 8-12V / 40 MA. |
| RTM1B | 1 BUTTON 2-WIRE QWIKBUS MODULE WITH BUILT-IN L.E.D. PRISM ILLUMINATION. L.E.D. OPERATES ON 8-12V / 40 MA. |
| RTM1BB | 1 BUTT 2-WIRE BUS MODULE-BROWN WITH BUILT-IN L.E.D. PRISM ILLUMINATION. L.E.D. OPERATES ON 8-12V / 40 MA. |
| RTM1BT | 1 BUTT 2-WIRE BUS MODULE-TITAN WITH BUILT-IN L.E.D. PRISM ILLUMINATION. L.E.D. OPERATES ON 8-12V / 40 MA. |
| RTM1BW | 1 BUTT 2-WIRE BUS MODULE-WHITE WITH BUILT-IN L.E.D. PRISM ILLUMINATION. L.E.D. OPERATES ON 8-12V / 40 MA. |
| RTM1T | 1 BUTTON STANDARD MODULE-TITAN WITH BUILT-IN L.E.D. PRISM ILLUMINATION. L.E.D. OPERATES ON 8-12V / 40 MA. |
| RTM1W | 1 BUTTON STANDARD MODULE-WHITE WITH BUILT-IN L.E.D. PRISM ILLUMINATION. L.E.D. OPERATES ON 8-12V / 40 MA. |
| RTM2 | 2 PUSHBUTTON STANDARD MODULE WITH BUILT-IN L.E.D. PRISM ILLUMINATION. L.E.D. OPERATES ON 8-12V / 40 MA. |
| RTM2A | 2 PUSHBUTTON 2-WIRE ALP MODULE WITH BUILT-IN L.E.D. PRISM ILLUMINATION. L.E.D. OPERATES ON 8-12V / 40 MA. |
| RTM2AB | 2 BUTTON 2-WIRE MODULE---BROWN WITH BUILT-IN L.E.D. PRISM ILLUMINATION. L.E.D. OPERATES ON 8-12V / 40 MA. |
| RTM2AT | 2 BUTTON 2-WIRE MODULE---TITAN WITH BUILT-IN L.E.D. PRISM ILLUMINATION. L.E.D. OPERATES ON 8-12V / 40 MA. |
| RTM2AW | 2 BUTTON 2-WIRE MODULE---WHITE WITH BUILT-IN L.E.D. PRISM ILLUMINATION. L.E.D. OPERATES ON 8-12V / 40 MA. |
| RTM2B | 2 BUTTON 2-WIRE QWIKBUS MODULE WITH BUILT-IN L.E.D. PRISM ILLUMINATION. L.E.D. OPERATES ON 8-12V / 40 MA. |
| RTM2BB | 2 BUTT 2-WIRE BUS MODULE-BROWN WITH BUILT-IN L.E.D. PRISM ILLUMINATION. L.E.D. OPERATES ON 8-12V / 40 MA. |
| RTM2BT | 2 BUTT 2-WIRE BUS MODULE-TITAN WITH BUILT-IN L.E.D. PRISM ILLUMINATION. L.E.D. OPERATES ON 8-12V / 40 MA. |
| RTM2BW | 2 BUTT 2-WIRE BUS MODULE-WHITE WITH BUILT-IN L.E.D. PRISM ILLUMINATION. L.E.D. OPERATES ON 8-12V / 40 MA. |
| RTM2T | 2 BUTTON STANDARD MODULE-TITAN WITH BUILT-IN L.E.D. PRISM ILLUMINATION. L.E.D. OPERATES ON 8-12V / 40 MA. |
| RTM2W | 2 BUTTON STANDARD MODULE-WHITE WITH BUILT-IN L.E.D. PRISM ILLUMINATION. L.E.D. OPERATES ON 8-12V / 40 MA. |
| RTM3 | 3 PUSHBUTTON STANDARD MODULE WITH BUILT-IN L.E.D. PRISM ILLUMINATION. L.E.D. OPERATES ON 8-12V / 40 MA. |
| RTM3A | 3 PUSHBUTTON 2-WIRE ALP MODULE WITH BUILT-IN L.E.D. PRISM ILLUMINATION. L.E.D. OPERATES ON 8-12V / 40 MA. |
| RTM3AB | 3 BUTTON 2-WIRE MODULE---BROWN WITH BUILT-IN L.E.D. PRISM ILLUMINATION. L.E.D. OPERATES ON 8-12V / 40 MA. |
| RTM3AT | 3 BUTTON 2-WIRE MODULE---TITAN WITH BUILT-IN L.E.D. PRISM ILLUMINATION. L.E.D. OPERATES ON 8-12V / 40 MA. |
| RTM3AW | 3 BUTTON 2-WIRE MODULE---WHITE WITH BUILT-IN L.E.D. PRISM ILLUMINATION. L.E.D. OPERATES ON 8-12V / 40 MA. |
| RTM3B | 3 BUTTON 2-WIRE QWIKBUS MODULE WITH BUILT-IN L.E.D. PRISM ILLUMINATION. L.E.D. OPERATES ON 8-12V / 40 MA. |
| RTM3BB | 3 BUTT 2-WIRE BUS MODULE-BROWN WITH BUILT-IN L.E.D. PRISM ILLUMINATION. L.E.D. OPERATES ON 8-12V / 40 MA. |
| RTM3BT | 3 BUTT 2-WIRE BUS MODULE-TITAN WITH BUILT-IN L.E.D. PRISM ILLUMINATION. L.E.D. OPERATES ON 8-12V / 40 MA. |
| RTM3BW | 3 BUTT 2-WIRE BUS MODULE-WHITE WITH BUILT-IN L.E.D. PRISM ILLUMINATION. L.E.D. OPERATES ON 8-12V / 40 MA. |
| RTM3T | 3 BUTTON STANDARD MODULE-TITAN WITH BUILT-IN L.E.D. PRISM ILLUMINATION. L.E.D. OPERATES ON 8-12V / 40 MA. |
| RTM3W | 3 BUTTON STANDARD MODULE-TITAN WITH BUILT-IN L.E.D. PRISM ILLUMINATION. L.E.D. OPERATES ON 8-12V / 40 MA. |
| RTM4 | 4 PUSHBUTTON STANDARD MODULE WITH BUILT-IN L.E.D. PRISM ILLUMINATION. L.E.D. OPERATES ON 8-12V / 40 MA. |
| RTM4A | 4 PUSHBUTTON 2-WIRE ALP MODULE WITH BUILT-IN L.E.D. PRISM ILLUMINATION. L.E.D. OPERATES ON 8-12V / 40 MA. |
| RTM4AB | 4 BUTTON 2-WIRE MODULE---BROWN WITH BUILT-IN L.E.D. PRISM ILLUMINATION. L.E.D. OPERATES ON 8-12V / 40 MA. |
| RTM4AT | 4 BUTTON 2-WIRE MODULE---TITAN WITH BUILT-IN L.E.D. PRISM ILLUMINATION. L.E.D. OPERATES ON 8-12V / 40 MA. |
| RTM4AW | 4 BUTTON 2-WIRE MODULE---WHITE WITH BUILT-IN L.E.D. PRISM ILLUMINATION. L.E.D. OPERATES ON 8-12V / 40 MA. |
| RTM4B | 4 BUTTON 2-WIRE QWIKBUS MODULE WITH BUILT-IN L.E.D. PRISM ILLUMINATION. L.E.D. OPERATES ON 8-12V / 40 MA. |
| RTM4BB | 4 BUTT 2-WIRE BUS MODULE-BROWN WITH BUILT-IN L.E.D. PRISM ILLUMINATION. L.E.D. OPERATES ON 8-12V / 40 MA. |
| RTM4BT | 4 BUTT 2-WIRE BUS MODULE-TITAN WITH BUILT-IN L.E.D. PRISM ILLUMINATION. L.E.D. OPERATES ON 8-12V / 40 MA. |
| RTM4BW | 4 BUTT 2-WIRE BUS MODULE-WHITE WITH BUILT-IN L.E.D. PRISM ILLUMINATION. L.E.D. OPERATES ON 8-12V / 40 MA. |
| RTM4T | 4 BUTTON STANDARD MODULE-TITAN WITH BUILT-IN L.E.D. PRISM ILLUMINATION. L.E.D. OPERATES ON 8-12V / 40 MA. |
| RTM4W | 4 BUTTON STANDARD MODULE-WHITE WITH BUILT-IN L.E.D. PRISM ILLUMINATION. L.E.D. OPERATES ON 8-12V / 40 MA. |
| RTMB-AM | RTMB BUTTON CONNECTOR BOARD |
| RU | AUX RELAY FOR STANDARD HANDSET USED WITH S.T.R. STANDARD TYPE HANDSETS TO PROVIDE A DRY CONTACT CLOSURE |
| RY008AE | 8 OUTPUT SIGNAL RELAY BOARD(S) REQUIRES CT032AE6 CABLE AND KE-PWR5/2A 5VDC POWER SUPPLY |
| RY012A | 12VDC RELAY--FORMC--10A@120VAC ROHS COMPLIANT |
| RY014B | RELAY FOR APT. STATION LIGHTS CAN BE USED AS A STAND-ALONE RELAY OR WITH APT. STATIONS HAS FORM 'C' TYPE OUTPUTS |
| RY019 | RELAY-DOLMEN SM 1-12H----PK543 |
| RY032AE | 32 OUTPUT SIGNAL RELAY BOARD REQUIRES CT032AE6 CABLE AND KE-PWR5/2A 5VDC POWER SUPPLY (1 EACH PER SYSTEM) |
| RY-18L | 18VDC POWERED FORM 'C' RELAY OPERATES ON 12VDC TO 18VDC INPUT |
| RY350B | 4-CHANNEL RADIO RELAY-SF301PIR USED WITH PILLOW SPEAKERS THAT HAVE 4-CHANNEL RADIO SELECTION INSTALLS INSIDE BED STATION(S) |
| RY351B | HILL-ROM SIDE-COM ADAPTOR UNIT (1 REQUIRED PER BED STATION) REQUIRES PL301 BLANK PLATE USED WITH IR319B / IR320B |
| RY-3DL | SELECTIVE DOOR RELEASE ADAPTOR |
| RY400 | 3-CONTACT RELAY ADAPTOR--SM400 PROVIDES 3- N/O CONTACTS FOR ELECTRIC DOOR RELEASE OR OTHER DEVICES. |
| RY402 | 3-REMOTE IN-USE ADAPTOR--SM400 USED WITH OR541U AND/OR IR141U REMOTE STATIONS. ONE (1) REQ. FOR UP TO THREE (3) REMOTES |
| RY502A | DUAL DOOR TIMED SWITCHER RELAY REQUIRES 16VAC TRANSFORMER FOR POWER (SS102A OR SS105B) |
| RY912 | 12 LINE RELAY BOARD--TEK ENTRY PLUGS INTO THE IH996 HOUSING/S USED WITH TEK-ENTRY III SERIES 'NO-PHONE-BILL SYSTEMS' |
| RY-AC | CALL EXTENSION RELAY--TBF/TBH |
| RYDTMF | DTMF TO RS232 DECODER BOARD HAS RCA AUDIO CONNECTOR JACK REQUIRES 7-24VDC PLUG-IN POWER SUPPLY (#SS12P OR EQUAL) |
| RY-PA | DOOR RELAY UNIT FOR LAF / LEF |
